10cm氙离子推力器变推力特性研究

非重力阻尼的连续、快速、高精度补偿是实现重力梯度测量卫星精细重力场测量的关键技术之一,直接影响到整星工程任务的成败。针对重力梯度测量卫星在轨飞行期间对电推进系统宽范围连续变推力能力的应用需求,分析了10cm氙离子推力器推力调节响应特性。在此基础上,通过对阳极电流、励磁电流和阳极流率等推力高敏感响应参量的组合调节,开展了推力调节试验研究,验证了10cm氙离子推力器宽范围连续变推力调节能力,获得了1～20mN范围内的推力调节性能及其变化规律。试验结果表明：在采用地面供电、供气设备条件下,10cm氙离子推力器能够在100～597W的功率范围内实现0.98～20.29mN的推力宽范围调节,比冲175～3500s,推力分辨率优于50μN。研究为建立10cm氙离子电推进系统的推力控制数学模型及调节控制算法奠定基础。     

应用傅里叶时间谱方法求解二维跨音速流动问题解的精度研究

为了从时间离散精度的角度评估傅里叶时间谱方法的实际计算效率,对用该方法求解二维跨音速流动问题的解进行了精度研究。通过求解Euler方程模拟俯仰振动NACA0012翼型的周期性非定常流动。结果表明:傅里叶时间谱方法可以使用很大的时间间隔较为准确地模拟有激波存在的周期性跨音速流动;对于此类流动问题,相比二阶向后差分公式法,傅里叶时间谱方法在预测翼型表面压力系数积分量特别是升力系数的时间变化规律方面具有明显的计算效率优势;用于模拟翼型表面压力系数自身的时间变化规律时,傅里叶时间谱方法具有不低于二阶向后差分公式法的计算效率。     

航空活塞二冲程汽油机排气口高度优化研究

针对作为无人机动力的某可变排气二冲程发动机在去掉可变排气系统后对发动机性能的影响，利用Fire仿真软件建立了发动机的缸内工作过程仿真模型，通过仿真和试验的方法研究了去掉可变排气系统后的发动机特性，结果表明:去掉可变排气系统后在2000r/min、10%节气门开度和5500r/min、50%节气门开度条件下，发动机的扫气效率降低，输出功率下降。在此基础上，利用仿真研究的方法对排气口高度参数进行了优化研究。去掉可变系统后排气口高度最优值为36.3mm时可以在保证常用无人机飞行转速范围内，各工况下扫气效率较高，发动机指示功损失最小，输出功率可以满足无人机动力需求。      

扰流环对粉末发动机燃烧流动影响的数值模拟

为了提高粉末火箭发动机的燃烧效率,通过数值模拟方法研究了扰流环的有无、通径及位置对燃烧室燃烧流动特性的影响。结果表明:扰流环会增强Al颗粒和气相的掺混和换热程度,促进Al颗粒蒸发和燃烧,从而提高粉末火箭发动机的燃烧效率。当扰流环通径比在0.538~0.846范围内时,扰流环的通径越小,燃烧效率越高;当扰流环头部距离比在0.3~0.8范围内时,扰流环位置离头部越近,燃烧效率越高。设计扰流环时,应在距离燃烧室头部30%~40%的位置布置小通径的扰流环。      

Multiscale eigenelement method for periodical composites: A review

Based on the eigenvector expansion idea, the Multiscale Eigenelement Method (MEM) was proposed by the author and co-workers. MEM satisfies two equivalent conditions, one condition is the equivalence of strain energy, and the other is the deformation similarity. These two equivalent conditions character the structure-preserving property of a multiscale analysis method. The equivalence of strain energy is necessary for achieving accurate macro behaviors such as lower order frequencies, while the deformation similarity is essential for predicting accurate micro behaviors such as stresses. The MEM has become a powerful multiscale method for the analysis of composite structures because of its high accuracy and efficiency. In this paper, the research advances of MEM are reviewed and all types of eigenelement methods are compared, focusing on superiorities and deficiencies from practical viewpoint. It is concluded that the eigenelement methods with smooth shape functions are more suitable for the analysis of macro behaviors such as lower order frequencies, and the eigenelement methods with piecewise shape functions are suitable for the analysis of both macro and micro behaviors.     

基于任务的微机电惯性系统规模化测试技术研究

针对传统惯性测试技术测试周期长、测试效率低、测试成本高等问题，提出了基于任务的微机电惯性系统规模化测试解决方案。研究分析了微机电惯性系统测试技术的研究现状和发展趋势，建立了基于任务的微机电惯性系统测试体系，详细论证了微机电惯性系统批量、并行、自动化测试解决方案的可行性，为微机电惯性系统规模化测试实践奠定了基础。     

一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

飞秒激光能量密度对镍基合金重铸层和加工效率的影响

以航空发动机叶片制孔为导向,结合飞秒激光对单晶镍基高温合金材料的非热熔性损伤阈值(Φth1)和热熔性损伤阈值(Φth2)特征,研究了飞秒激光能量密度(0Φ44.2J/cm2)对制孔重铸层和加工效率的影响规律。研究结果表明:在Φth1ΦΦth2时,镍基合金经飞秒激光加工后加工侧壁没有出现明显的重铸物;在ΦΦth2时,加工侧壁开始出现重铸物,并随着能量密度的增加,重铸层厚度增大。在试验结果的基础上,建立了飞秒激光单脉冲加工深度与能量密度的定量关系。能量密度越高,飞秒激光单脉冲加工深度越大,加工效率越高。     

基于任意多项式中弧线的单级高效率风扇设计

为了在压气机通流设计阶段考虑叶片弯掠效应,开发了基于流线曲率法的通流设计程序,提出一种基于四次多项式的任意中弧线叶片造型方法,并推导了任意回转面上的中弧线表达式。以此方法为基础,采用通流设计与叶片造型相互迭代的方式开展大流量跨声速风扇设计研究。此风扇级的设计点为巡航状态,设计流量为155kg/s、压比为1.54。研究结果表明:在设计状态,此风扇级的总压比为1.545,转子和级效率分别为0.939、0.916;在设计转速下,失速裕度为17%,转子和级最高效率分别为0.945、0.923;在起飞状态,流量接近440kg/s,效率与巡航状态相当,压比高于巡航状态。     

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Vegetable oil can be used as a base oil in minimal quantity of lubrication(MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force,and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that(1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and(7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force,87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy ratio coefficient.